The publisher is making several great points on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround in general in this great article just below.
Installing a tub isn't specifically rocket science, but it does need strong plumbing, woodworking, and often, tiling abilities. Changing an old bathtub with a new one is likewise a reasonably hard project. If the old tub is easily easily accessible, the task can relocate quickly; if you have to open up a wall surface to get rid of the old tub and position the brand-new tub, the job is a lot harder. In either instance, the project is within a home handyman's skills, although you will require an assistant to vacate the old bathtub as well as embeded in the brand-new one. Make sure you have qualified yourself for the task as well as fit trying it. As opposed to working with a contractor to take over a halfway-completed project, it is better to consider employing one before you begin. Chances are you may need a professional plumber to make tube connections.
This article will certainly aid you mount a brand-new bath tub in your washroom if you have actually currently acquired a brand-new bathtub and also do not require to change the plan of your previous supply of water pipes.
Your tools and material checklist should comprise the following:
Planning for the Installment
To start with, the sustaining framework supplied with the bath should be fitted (if required) according to the manufacturer's directions. Next, fit the taps or mixer to the bathtub. When suitable the faucet block, it is very important to make certain that if the tap comes with a plastic washing machine, it is fitted between the bath and the faucets. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the faucets system to prevent strain on the bath tub.
Fit the adaptable tap connectors to the bottom of both taps making use of 2 nuts and also olives (often supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet with the hole in the bath. Make use of the nut provided by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which must be fitted inside the bath. Make sure you use every one of the supplied washing machines.
Link the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bath must now prepare to be fitted in its last setting.
Removing Old Taps
If you require to change old taps with brand-new ones as a part of your setup, then the first thing you must do is disconnect the water system. After doing so, turn on the faucets to drain any kind of water staying in the system. The procedure of removing the existing taps can be fairly problematic as a result of the restricted accessibility that is frequently the instance.
Use a container wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipes to the faucets. Have a cloth all set for the remaining water that will certainly originate from the pipes. As soon as the supply pipes have actually been gotten rid of, utilize the very same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly need to quit the single faucets from turning during this procedure. Once the taps have actually been removed, the holes in the bath/basin will have to be cleansed of any old sealing substance.
Prior to proceeding to fit the brand-new faucets, compare the pipeline links on the old taps to the new faucets. If the old taps are longer than the brand-new faucets, then a shank adapter is required for the brand-new faucets to fit.
Installing the Tub
Making use of both wood boards under its feet, place the tub in the needed placement. The wooden boards are valuable in uniformly spreading the weight of the tub over the location of the boards as opposed to focusing all the weight onto four little factors.
The following goal is to ensure that the bathtub is leveled all round. This can be achieved by inspecting the level and also adjusting the feet on the bathtub until the spirit level reads level.
To set up faucets, fit all-time low of the outermost flexible tap connector to the suitable supply pipeline by making a compression sign up with; after that do the very same for the other tap.
Switch on the supply of water and examine all joints and also brand-new pipework for leaks and tighten them if required. Fill up the tub and likewise inspect the overflow outlet as well as the typical outlet for leaks.
Lastly, repair the bath paneling as explained in the maker's user's manual. Tiling as well as securing around the tub must wait up until the tub has actually been utilized at least when as this will certainly resolve it right into its last placement.
Suitable New Touches
If the tails of the new taps are plastic, after that you will certainly require a plastic port to avoid damages to the thread. One end of the connector fits on the plastic tail of the tap and the other end gives a link to the current supply pipelines.
If you need to fit a monobloc, then you will require decreasing couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next, place the faucet in the installing hole in the bath/basin ensuring that the washing machines remain in location between the tap and the sink. Safeguard the faucet in place with the producer provided backnut. As soon as the faucet is safely in place, the supply pipelines can be attached to the tails of the taps. The taps can either be connected by utilizing corrugated copper piping or with typical tap connectors. The previous type should be attached to the faucet finishes initially, tightening only by hand. The supply pipelines can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have been connected.
Tiling Around the Bath tub
In the area where the bath fulfills the ceramic tile, it is necessary to secure the joins with a silicone rubber caulking. This is essential as the fitting can relocate sufficient to break an inflexible seal, triggering the water to penetrate the wall between the bathroom and the tiling, leading to issues with dampness and also possible leaks to the ceiling listed below.
You can choose from a selection of coloured sealants to assimilate your fixtures and also fittings. They are marketed in tubes as well as cartridges, and can sealing gaps approximately a width of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with spins of soaked paper or soft rope. Keep in mind to constantly fill up the bath tub with water before securing, to allow for the activity experienced when the tub remains in use. The sealer can crack relatively early if you do not take into consideration this movement prior to sealing.
Additionally, ceramic coving or quadrant floor tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are additionally quickly readily available on the market. It is a good idea to fit the tiles utilizing waterproof or waterproof sticky and also grout.
How to Install a Freestanding Bathtub?
Installing a freestanding bathtub or any kind of bathtub is not a difficult task if you have a sophisticated guide on installing a freestanding bathtub in your bathroom. Aside from getting the freestanding bathtub to your bathroom, you can do all the work without paying a plumber. A bathroom with a bathtub is a retreat where you can feel the sensation of coming home and soaking in that hot water. It is a great way to remove all the stress from your day.
This guide will walk you through installing a freestanding bathtub in simple steps and help you find relief.
Slope
Make sure your bathroom has a proper slope. If your floor lacks a slope, the water flow to the drain will not function, which leads to a blocked drain which can cost you money. You can use the level device to see your bathroom's vertical and horizontal aspects. Once you have that information, you must carry out the next step.
Placement
A freestanding bathtub has a unique characteristic that helps you bring elegance to your bathroom. A freestanding bathtub comes in various sizes and shapes suitable for different types of bathrooms.
According to the information you gathered from the level device, you must pick a bathtub that suits your style and fits your bathroom aesthetically. You can place a freestanding bathtub virtually anywhere, such as in the corner, near the wall, or even at the center of your bathroom. However, you must ensure proper plumbing where you want to install the tub. If not, then you must call a plumber.
Clean the bathroom floor
After deciding where to place the bathtub, you must clean the entire bathroom floor so that the dust and debris do not accumulate underneath the tub. Simple cleaning is enough, and you will clean it again after the installation.
Steps to Install a Freestanding Bathtub:
STEP 1: Place the protective blanket in the adjacent area where you want to install the bathtub. It will help you protect the bathtub's sides when you do the installation.
STEP 2: Now, place the 4x4 lumber in the area where you want to install the bathtub. Place the bathtub on top of the lumber, and align the drain line with the bathtub drain.
STEP 3: A freestanding bathtub comes with a drain kit. If not, make sure you purchase one with your bathtub. You can pop that drain kit and align it with your bathroom drain line. Ensure that you tighten the drain nut enough so there is no water leakage. You must also clean the bathtub’s drain to remove the factory dirt and debris.
STEP 4: Clean the drain hole in your bathroom. It helps to do the installation without any water blockage. A drain cleaner or bleach will suffice. Once the drain dries entirely, take a small amount of clear silicon and place it around the underside of the pipe flange.
STEP 5: Attach the drain tailpiece to the bottom of the bathtub. Place the rubber or plastic bushing with the plumbing material at the top of the tailpiece and screw the drain nut up the tube until it tightens both the bathtub’s drain and the drain tailpiece. Now you must add the lubricant to the seal to ensure there is no water leakage in the pipe connection.
STEP 6: Place caulk around the bottom edge of the bathtub. Take out the lumbar support and carefully bring the bathtub to the floor. Use a damp cloth to clean the excess caulk and debris and plumber putty to cover the tub drains and the floor.
Tips to Maintain a Freestanding Bathtub:
Always look for the clog in the drain. You can pull it out with a small stick if hair or debris is in the gutter. Use mild cleaning components, which will help you preserve the bathtub for a long time and will also help you remove surface-level scratches. Do not use strong solutions such as concentrated bleach to remove stains. Instead, mix water and diluted bleach with a ratio of 10:2, respectively. Apply it to the tub's surface and leave it for 15-20 minutes to remove any surface-level stains. Always check the floor drain. You may unclog it using any small sticks or a small vacuum to suck out all the debris. Check the heater or faucet immediately if you smell rust or grease in the water. Rust in the water may stain or damage the bathtub in the long run. If you want to sand the bathtub, try using 400 grit sandpaper or 600 grit sandpaper for a more refined finish.
Hopefully you liked our article on A Step-by-Step Guide to Installing a Bathtub. Many thanks for taking time to read our post. Appreciated our entry? Please share it. Help other people find it. Thank-you for your time spent reading it.
Show Details